Shop

/Shop
  • You'll enjoy added rear visibility on your motorcycle with the Flashback Flat Mount Kit. This option is for flat surfaces such as tour packs, back rests, and trailers. Flashback Flat Mount Kit also includes a rubber trim gasket. This provides a factory-quality look to the light. Need help ordering? Call us for support at (480) 209-0764
  • The Flashback License Plate Mount option is our most popular seller for increasing rear end visibility of your motorcycle. You simply remove the license plate. Add the Flashback plate. The re-install the license plate and frame with your existing hardware. The Flashback License Plate Mounts allow for you to customize to your liking. You can adjust the plate up or down. You can also adjust the light angle by bending the plate at the cut line. The goal of any light angle adjustment is to be the same as the projection angle of your tail light.
  • Motorcycle riders around the world love the Lightning Strike Bullet Switch. It's ergonomically designed for safety and ease of use. Easy to find on your handlebars. This is essential, especially in those moments when you need it most. Designed for ease of use even if you wear riding gloves.
  • The tapered mount kit is similar to the bar mount. However, it also includes a 10-degree taper built into it. The tapered mount kit is ONLY AVAILABLE IN THE 1.25 BAR DIAMETER SIZE. That's 1  1/4 inches. This mount was made especially for engine guards. This is because they often have a swept-back design built into it. The tapered mount will mount bear your footpegs. It will correct the light angle to be straight-ahead, without the use of shims (in most cases). Need help ordering? Call us at (480) 209-9762. Kit includes: 2 Tapered Mounts 2 LED Light Modules Mounting Hardware Wire and Connectors Bullet Switch Installation Instructions switch-clamp-measurement NOTE: To complete your order, we need you to give us the diameter of your left-hand grip. Using a tape measure or caliper, measure the area where the stainless steel bullet switch clamp will mount. A nice snug fit is required to prevent the clamp from moving when the switch button is depressed. (Example: 1.25"). Include the measurement in the space provided at checkout. We will include the proper size clamp with your order.
  • The bar mount kit features a straight mount. It simply attaches the light to a particular bar diameter. Bar mount kits are available in two sizes: 1.25" (1  1/4 inch) and 1.50" (1  1/2 inch). The positioning of the mount should be such that when attached to the bar, the light points in the same direction as the headlights. The positioning is important. This provides you with the brightest effect of the light as seen by a motorist). Need help ordering? Call us at (480) 209-9764. Bar Mount Kit includes: 2 mounts of your choice 2 LED light modules Hardware Wiring and Connectors Bullet Switch Installation Instructions   switch-clamp-measurement NOTE: To complete your order, we need you to give us the diameter of your left-hand grip. Using a tape measure or caliper, measure the area where the stainless steel bullet switch clamp will mount. A nice snug fit is required to prevent the clamp from moving when the switch button is depressed. (Example: 1.25"). Include the measurement in the space provided at checkout. We will include the proper size clamp with your order.    
  • The flat mount kit is so easy. It is the most simple style we sell. It uses no mount other than the light itself, and it attaches firmly to any flat surface. A rubber trim gasket is included for each light in the kit. This makes for a clean look when mounted. Need help ordering? Call us at (480) 209-9764. Bar Mount Kit includes: 2 LED Light Modules Rubber Trim Gasket Installation Hardware Wiring and Connectors Bullet Switch Installation Instructions   switch-clamp-measurement NOTE: To complete your order, we need you to give us the diameter of your left-hand grip. Using a tape measure or caliper, measure the area where the stainless steel bullet switch clamp will mount. A nice snug fit is required to prevent the clamp from moving when the switch button is depressed. (Example: 1.25"). Include the measurement in the space provided at checkout. We will include the proper size clamp with your order.    
  • The fork mount is similar to the tapered mount. But  it includes a 30-degree taper built into it.  It is only available in the 2.25" bar diameter size, which will fit most fork diameters.  This mount was made especially for forks, which are often at a 30-degree rake.  The fork mount will correct the light angle to be straight-ahead, without the use of shims (in most cases).  Note:  These mounts are glued in-place.  No screws can go into forks or damage to the fork will occur. Need help ordering? Call us at (480) 209-9764. Fork Mount Kit includes: 2 LED Light Modules Installation Hardware Wiring and Connectors Bullet Switch Installation Instructions   switch-clamp-measurement NOTE: To complete your order, we need you to give us the diameter of your left-hand grip. Using a tape measure or caliper, measure the area where the stainless steel bullet switch clamp will mount. A nice snug fit is required to prevent the clamp from moving when the switch button is depressed. (Example: 1.25"). Include the measurement in the space provided at checkout. We will include the proper size clamp with your order.    
  • Out of stock
This website uses cookies and third party services. Accept